January 10, 2002, read first time and referred to Committee on Agriculture and Small
Business.
Introduced
Second Regular Session 112th General Assembly (2002)
PRINTING CODE. Amendments: Whenever an existing statute (or a section of the Indiana
Constitution) is being amended, the text of the existing provision will appear in this style type,
additions will appear in
this style type, and deletions will appear in
this style type.
Additions: Whenever a new statutory provision is being enacted (or a new constitutional
provision adopted), the text of the new provision will appear in
this style type. Also, the
word
NEW will appear in that style type in the introductory clause of each SECTION that adds
a new provision to the Indiana Code or the Indiana Constitution.
Conflict reconciliation: Text in a statute in
this style type or
this style type reconciles conflicts
between statutes enacted by the 2001 General Assembly.
SENATE BILL No. 381
A BILL FOR AN ACT to amend the Indiana Code concerning
health.
Be it enacted by the General Assembly of the State of Indiana:
SECTION 1.
IC 16-18-2-242.9
IS ADDED TO THE INDIANA
CODE AS A NEW SECTION TO READ AS FOLLOWS
[EFFECTIVE JULY 1, 2002]: Sec. 242.9. "MTBE", for purposes of
IC 16-44-2
, has the meaning set forth in
IC 16-44-2-2.4.
SECTION 2.
IC 16-44-2-2.4
IS ADDED TO THE INDIANA CODE
AS A NEW SECTION TO READ AS FOLLOWS [EFFECTIVE JULY
1, 2002]: Sec. 2.4. As used in this chapter, "MTBE" refers to the
gasoline additive methyl tertiary butyl ether.
SECTION 3.
IC 16-44-2-8
IS AMENDED TO READ AS
FOLLOWS [EFFECTIVE JULY 1, 2002]: Sec. 8. (a) The inspections
and tests made by the state department under this chapter shall be
conducted in accordance with the methods outlined by the American
Society for Testing and Materials.
(b) The inspections and tests as to gasoline, gasohol, and kerosene
must reflect the following minimum specifications necessary for the
approval of the product:
(1) Gasoline or gasohol:
(A) Corrosion Test . Method ASTM D-130. A clean copper
strip may not show more than extremely slight discoloration
when submerged in the gasoline for three (3) hours at one
hundred twenty-two (122) degrees Fahrenheit.
(B) Distillation Range . Method ASTM D-86. When the
thermometer reads one hundred sixty-seven (167) degrees
Fahrenheit, not less than ten percent (10%) may be evaporated.
When the thermometer reads two hundred eighty-four (284)
degrees Fahrenheit, not less than fifty percent (50%) may be
evaporated. When the thermometer reads three hundred
ninety-two (392) degrees Fahrenheit, not less than ninety
percent (90%) may be evaporated. The residue may not exceed
two percent (2%). Percent evaporated is found by adding the
distillation loss to the amount collected in the receiver at each
specification temperature.
(C) Sulphur . Method ASTM D-1266 or D-2622. Sulphur may
not exceed twenty-five hundredths of one percent (0.25%).
(D) Vapor Pressure . Method ASTM D-4953, ASTM D-5191,
or any other ASTM method to determine vapor pressure
approved by the United States Environmental Protection
Agency. For gasoline, the Reid vapor pressure at one hundred
(100) degrees Fahrenheit may not exceed the following:
(i) Fifteen (15) pounds per square inch at the normal
barometric pressure at the point of delivery during
November, December, January, February, and March.
(ii) Fourteen (14) pounds per square inch during April and
October.
(iii) Twelve (12) pounds per square inch during May, June,
July, August, and September.
(E) For gasohol (a blend of gasoline and alcohol permitted
under federal tax requirements), the vapor pressure may not
exceed the following:
(i) Sixteen (16) pounds per square inch during November,
December, January, February, and March.
(ii) Fifteen (15) pounds per square inch during April and
October.
(iii) Thirteen (13) pounds per square inch during May, June,
July, August, and September.
(F) After July 23, 2004, gasoline may not contain more
than one-half percent (0.5%) of MTBE by volume.
(2) Kerosene:
(A) Flash Test . Method ASTM D-56. Flash point may not be
lower than one hundred (100) degrees Fahrenheit.
(B) For the purpose of this chapter, any petroleum product
designated by name or reference as "kerosene" must meet the
federal specifications for kerosene VV-K-211d in effect on
March 1, 1977.
(c) Gasoline, gasohol, and kerosene products that do not comply
with the minimum specifications described in subsection (b) may not
be sold, offered for sale, or used in Indiana.
(d) Petroleum products other than gasoline, gasohol, or kerosene
shall be inspected and tested by the methods as are necessary to
determine the contents and characteristics of the product.